sony bravia ir blaster This is a topic that many people are looking for. bluevelvetrestaurant.com is a channel providing useful information about learning, life, digital marketing and online courses …. it will help you have an overview and solid multi-faceted knowledge . Today, bluevelvetrestaurant.com would like to introduce to you IR Blaster Product Preview. Following along are instructions in the video below:
“Hello and welcome to another episode of the hauppage product preview. I m stephen your your host and today we re going to talk about the ir blaster and how set it up the ir blaster is a black cable with three ends. The ir blaster plug in the ir blaster and the ir receiver on certain hauppage products. The ir receiver is built right into the front of the device along with the cable.
We provide additional velcro stickers and double sided tape for mounting each end. So i ve already connected our power supply. Our set top box. And the usb that leads to our computer.
And all that s left to set up is our ir blaster. Now we ll go step by step through the setup first plug the ir blaster cable. That came with your happauge product into the ir receiver jack next position the ir receiver. Where it is visible and unobstructed from the light of the remote make sure that our wind tv application is already installed on your computer.
And the program. Ir. 32. E x.
E. Is running then check that your remote control..
Is working. Just make sure that the remote has good batteries and then point. The remote at the ir receiver and press. The go button on the remote.
You should then see win tv open up on your desktop. Once you ve checked your remote control install the ir blaster on the set top box to guarantee that your commands are sent to your set. Top box. Properly position the ir blaster over the receiver of your set.
Top box your next. Step will be to configure your blaster channels click on the settings button and go to the devices tab highlight your hauppage tv tuner device and click tuner setup. You will then see the device setup wizard with your win tv device specified put a check in the box that matches. Your sources signal type.
And then click next you ll then be asked to choose the connection you plan on using s video composite. Or tuner if you select tuner you ll also need to identify the channel. The boxes tuned to be sure to place a checkmark in the box that reads use ir blaster to control stb and then click next in the next window. You ll need to manually.
Add your set top box tv. Channels to the wind tv..
Channel list enter. The tv channel. Number and name and click add repeat. This process for each tv channel.
You wish to receive through your set. Top box. Now you have a list of set top box channels. When tv can automatically tune to when you re done click next.
It s time to configure the ir transmitter to control your set top box. Like universal remote controls. The hauppauge ir. Remote blaster has a list of common set.
Top boxes. Which it can control and like universal remote controls. You must test various codes from the list to see. Which one applies to your specific set top box.
Here s how to do it. First run the blasts cfg you can find blasts cfg by clicking start programs..
Hauppauge. Win tv. And there. It is note that if some controls are grayed out it means.
The ir remote blaster hardware is not found on your win. Tv. Make sure. The ir remote blaster cable is firmly plugged in now.
Select your region select the device cable or satellite. Then vendor and model of your set top box. The code set will contain a list of codes. Which the ir remote blaster knows about the selected vendor.
There might be as many as 10 codes for the vendor chosen push the power on off button and you should see the ir transmitter blink after each time you press. It if your set top box turns on or off. Then this code is the correct one for your set top box. If not click test next continue to click test next.
Until your set top box turns on or off at which time you have found the correct code. If you cannot find a code..
Which works with your set top box first make sure the ir transmitter is positioned over the remote sensor on your set top box. Remember the ir transmitter has a very short range and needs to be positioned directly over the remote sensor on your set top box. If you still cannot find the correct code for your set top box after adjusting the ir blaster click the test all button this button will go through all of the codes in our database of set top boxes after clicking test all watch your set top box. If it goes on or off immediately click stop test you have found the correct code for your set top box.
If your set top box does not turn on or off even after going through all the codes. Then either the ir transmitter is not positioned correctly or your box is not support. It. If your box is not supported check out our video called how to learn stb codes.
There you ll find the support that you need once you have determined the code you can click the send button to send a number sequence to your set top box. If your set top box is on you should see 1 2. 3. Appear on the channel indicator of your set top box.
Close the blaster configuration program to save the configuration and you re done. That s it you should now be able to use the win tv scheduler to automatically record shows from your set top box. Well that ll wrap up this episode of the happauge product preview from all of us at hauppage. Thank you for watching.
I hope this video was helpful for you if you have any questions or want to learn more about our products at us and like us on facebook or you can ” ..
Thank you for watching all the articles on the topic IR Blaster Product Preview. All shares of bluevelvetrestaurant.com are very good. We hope you are satisfied with the article. For any questions, please leave a comment below. Hopefully you guys support our website even more.