what is the most convenient way to represent the niobium wire in your figure? This is a topic that many people are looking for. bluevelvetrestaurant.com is a channel providing useful information about learning, life, digital marketing and online courses …. it will help you have an overview and solid multi-faceted knowledge . Today, bluevelvetrestaurant.com would like to introduce to you How to Form Shapes Out of Wire | Jewelry 101. Following along are instructions in the video below:
Guys. Susan thomas here and today i want to teach you how to form shapes shapes out of wire. Okay.
So i really like to take heavier gauge. Wires and shapes out of them like leafs and kites and circles. So that i can make different types of jewelry like big hoop earrings or big pendants that you can wire wrap lots of different stones on to so.
I think. Its a really fun thing to know how to do so you can change up what you can do when youre making your jewelry. So follow along and i think youll really really like this its skill now youre gonna need some tools and of course as always youre going to need your basics youll need a round nose plier.
You will need a chain nose plier and you will need a flush cutter. Absolutely have to have those i also like to have a flat nose plier when im doing this type of skill and then other metalworking tools that are very helpful chasing hammer and a bench block and thats for being hardening and reshaping your wire. And then of course your handy.
Rawhide hammer and then its also nice to have some manuals like a ring mandrel is good for shaping wire. And also a bracelet mandrel is really great for shaping wire. And then finally i love to have specialty tools to make different shapes.
And im going to use this one today. It is a triangle mandrel cool right. Im gonna use this to show you how to make a kite out of wire.
So thats a lot of fun to have as well and then as far as supplies are concerned youre just gonna need some heavier gauge wire. Im gonna use 16 gauge today because its nice and heavy and it really holds its shape when you make it into these larger kind of loopy shapes. 16 gauge 18 gauge 14 gauge.
Those are the best gauges to use to make these types of shapes alright. So were just gonna start out with a basic shape. Were gonna make a hoop because to me hoop earrings are just my absolute favorite thing to wear theyre classic everybody loves them so ill show you how to do that first just using this wire.
So im gonna pull off some 16 gauge wire and im gonna pull off a pretty good amount. Im gonna take about a foot of wire. What im gonna do is just cut that with my cutter like so and then im gonna use my bracelet mandrel.
This is a round manjula. See how its round all the way around and one of the things thats almost impossible to do when youre making jewelry is to make a circle a perfect circle. I could try.
But its not gonna be very pretty so its great to use something like this to form your shape and also these are fun because theyre graduated. So i could make a small hoop or i could come all the way down here at the bottom and make really really big hoops. So im just gonna take this right here kind of up towards the top of the mandrel and im just gonna overlap.
My wires on either side like so and im holding it tight to the mandrel to keep that shape usually when i do this i do two at the same time so theyre exactly the same size or close to exactly the same size since im i would be maybe making a pair of hoop earrings and i would like them to be the same size. So im just holding that right there on my mandrel and just not leaving any space or air between the mandrel and my hoop and then im gonna grab one of these pieces of wire. Im gonna bend it out into an angle like so so im going to take that off so you can see what ive done really nice circle.
There and then ive got my two pieces of wire. This is going to end up being a hoop at the top or a little loop at the top to hang it off something and this piece is what im going to use to finish this off. So now what im going to do is im going to take remember.
I said id like to use flat nose pliers you can use chain nose pliers to do this. But i like to use flat nose. Personally its a definitely a personal preference.
Im just going to hold on to my wires right here and take this piece of wire and wrap it around the other piece of wire a couple times like so and im just going to take that squeeze that in just like that and let me get that around to the back. I want to trim it off at the back so ill just take your flush cutter and trim off the extra wire and use that flat nose or chain nose plier to squish that down in the back. Now.
What im gonna do is im going to take this piece and im going to bend it off to the side like so. Because i want to make a little loop at the top because this is going to be a hoop earring. Eventually and so im just gonna cut this about 3 8.
Of an inch long and im gonna take my round nose plier and just roll that into a circle a little bit more centered tada. So you see ive two of those. And you have a cute little pair of hoop earrings alright so that was easy if you want to what you can do like say like it it maybe isnt quite as round as you want you can put it back on to your mandrel hammer.
It out with your rawhide hammer like so and make it a little bit more circular and then if its a little bit wavy. Like i think this ones a little bit wavy. You can put it on your bench block and take your rawhide hammer or even your tasting hammer and just kind of shape that up like so okay so thats easy right lots of fun you could make tons of things you can hang things off of these you can wrap things on them really just a fun easy classic shape now next up im gonna show you how to make a leaf shape and so im just gonna grab about a foot of wire again and im gonna take my flat nose plier and im gonna bend this in half right in the center thats how i bent that in half and then im just gonna squeeze those two pieces together and i like to squeeze it into a pretty good point.
Im going to take my flat nose plier and im just going to squeeze down at the bottom and to me the tighter you squeeze. It the better it looks the more it looks pointing at the bottom okay so now. This is what youve got basically just a piece of wire folded in half and then im just going to open this up a little bit.
So i have a v shape. And then next thing. I do i like to use a ring mandrel the end of a ring mandrel to do this.
A dowel will work just fine as well this is just what i usually have around so its what i use so. What im going to do is im just going to put this on to the end of the ring mandrel and push it up a little bit and then push those two wires over on either side to make my leave shape. And if you want to like if you take it and kind of squeeze at the bottom here.
Itll give it a little bit more definition like so. So then basically the same thing as we just did with the hoop is youre gonna grab one of these wires and bend it up into an angle and then take your flat nose plier and hold on to both of these you really want to hold these pretty tight because i have found that if you dont hold both sides of this shape. One side will end up smaller than the other one and i want them to be as even as i possibly can get them alright so two times around see how cute that is its fun and then trim off the extra wire just like you did on the hoop squeeze down im gonna bend.
This the other direction back and forth because you could make this into a pendant if you wanted to you could have you could wrap beads on here. If you wanted to or just dangle one thing from the bottom. It would look really cute so im bending this back of this direction and trim this off about 3 8.
Of an inch take your round nose plier roll that into a circle. And now that could be a little pendant like you could dangle. Something you can even put a tassel off the bottom of that and it would be really really cute and the same thing as before if you want to kind of flatten this out or strengthen.
It a little bit especially if you used like i used 16 gauge wires. This is really strong. But maybe i used 18 gauge and its a little bit lighter wire and you want to make it a little bit stronger you can take it and just hammer it out just a little bit using your chasing hammer and that will put a little bit of texture on it but its okay and you can even if you wanted to like really really hammer.
It out and make it flattened out so see pretty fun alright now one more shape now. This is fun. Im going to show you how to use this tool.
Its a weber. These were these were invented by a lady named patty bullard. Shes just amazing.
But i think that that is so cool so same thing. Im just going to trim off about a foot of wire. And then i am going to put my wire between the jaws of the triangle weber and i am going to make a complete triangle.
How i did that and then what youre gonna do is youre gonna open one side of the triangle. Its better to do if you have it still inside here and then im going to open up the other side and the farther. I open it the bigger kite.
Ill have i like this one this ones really really fun to design with too because you can dangle things off the bottom you can wrap things in here you can wrap things across this and it just looks fantastic. So now you have to decide like how long youre a big you want your kite to be so. Maybe i want to open.
It up a little bit more make it a little bit bigger and then squeeze. These two guys in see how that works and then you want to finish it the same way we finished. The other guys so im just going to take it right there where it criss crosses and bend that up into an angle.
Hold both sides and wrap the wire around just like so two times and finish that off okay and then were just gonna trim off the extra wire at the back and im gonna squeeze these together just a little bit because they got just a little bit loose. There we go and then im gonna bend that off to the side trim off this about 3 8. Of an inch again so i can make my loop at the top round nose plier and roll into a loop.
Now i have a kite a leaf and hoop pretty cool this ones probably my favorite i love it im gonna hammer it out just a little bit and ive done different designs its cute if you put little wraps down here on the bottom. Like you could put a couple turquoise here. A couple turquoise here and then maybe a drop or something off the bottom.
Its fun to fill it halfway up with all kinds of different beads different colors. Just really cute do the same types of things with these i like to wrap beads around the outside and around the insides of these and these i just theres so many different things you can do you can wrap beads along one side of it if you want to across the center dangle. A tassel whatever you like lots of fun great design ideas.
I hope you guys like learning how to form shapes out of wire. Dont forget the tools and supplies that you need to be successful doing this technique. Youre gonna need a round nose plier.
A chain nose or a flat nose plier and a flush cutter and then its really great to have some shape forming tools like a mandrel. This is a bracelet mandrel and this is a ring mandrel which i love and then i also have a specialty forming tool. This is a weber that is a triangle shape.
Which was great for making our kite additionally. Its a good idea to have for any metal working a bench block and a chasing hammer and i have my favorite. My rawhide hammer as far as supplies are concerned you really just need some heavier gauge wire like the 16 gauge that i use today thanks so much for watching guys if youd like to pick up some supplies like the ones.
We work with today check out the links down below. Whats the crazy and shape you can imagine making out of wire. Dont forget to like and subscribe and ill see you again next time music.
Thank you for watching all the articles on the topic How to Form Shapes Out of Wire | Jewelry 101. All shares of bluevelvetrestaurant.com are very good. We hope you are satisfied with the article. For any questions, please leave a comment below. Hopefully you guys support our website even more.