cyberpunk visor This is a topic that many people are looking for. bluevelvetrestaurant.com is a channel providing useful information about learning, life, digital marketing and online courses …. it will help you have an overview and solid multi-faceted knowledge . Today, bluevelvetrestaurant.com would like to introduce to you How to LED GLOW VISOR. Following along are instructions in the video below:
“I can t wait to start recording. Yeah. Yeah. Oh yeah.
It s gonna be be a lot of fun. There s gonna be so much that we re going be covering let me know when we start recording by that we ve been recording hey guys how they hear from our mary props and welcome to our first how to tutorials in this video. I m going to be covering how to make the hexagon glow. Vibrant while recovering.
What you ll need and how to put it all together. So let s get to it let s go over the material. You re gonna need so you re gonna need a sheet of ptg point zero six. Think you re gonna need a template for the helmet.
You re gonna use you re going to need led strips. I get these on amazon. They re fairly cheap and they come in a lot of colors..
You re going to also need a painting. Copy blade wire batteries. Specifically the 21. By 23 tape.
Solder wire a switch. This is an on and off switch. You can get on amazon to your need battery case fidget spinner slaughter pen super saiyan hair you re gonna need your template glue gun and of course a sharpie so what we re gonna do now is we re going to apply the hex pattern on top of gptt sheet that we have here and the way. I like to start that is by taping off the edges onto the sheet.
So that it s easier to remove the backing late so one thing. I did forget to mention is you re gonna need a frosting spray the brand that i like to use is by kryolan glass. And it s a frosting interior spray what we re gonna do is we re gonna apply a couple of coats on top of the hexagon pattern. We re gonna let it dry and then we re gonna cut it up and then from there we ll move on to the next step once you have the shape that you want cut out what we re gonna do now is we re gonna peel off the hexagon frame.
So that we can apply the leds onto the sides once you ve remove the hex frames from the ptg. We re gonna get it ready for the led strips for the next part. We re gonna need all of our soldering material including the batteries the wire the blue gun the switch battery case and of course the led strips so let s start off with the led strip..
What we re gonna do is we re gonna cut off little sections and we want to make sure that whenever we cut them off. We cut them off at the dividing point. They ll be a little indicator as to where to cut. And here s a closer look to what i mean about the dividing point.
It ll be right between these two copper points. When you re just gonna cut right there. And you have a perfect led strip the next thing. We re going to do is we re gonna place soldered to the copper points on every side.
And there are four points to each one so so what we re gonna do now is we re gonna measure out how much wire whitney. What i like to do here is i like to measure out from endpoint to endpoint on the vitamin. So. I m gonna start on this side advisor.
Real quick and then i m just going to measure it out all the way to the other end and that gives me about roughly how much i m ready once you ve got all your wires cut out we re gonna strip the end of them to expose the wire inside this is so that we can solder it on to the led strips once you have the end of the wire strip. You re gonna go ahead and slide are those on to the end points of the led strips and you want to make sure that you solder from negative to negative positive to positive so now we re gonna add power to the led strips so what you re going to need your battery case and we re going to start off with the positive end so i m going to connect the red to the positive part of the led strip from here we re going to take our switch and we re gonna add the negative part to one end of the switch. But you want to expose the wires..
A little bit more this one was fairly out and i think i ve cut some of the wires off so i wanted i stripped it again and i m gonna troll it a little bit to make sure that we have something for it to connect or to be able to twirl around little loops here make sure you get it nice and cold. You don t want to have any of the hairs flying out cuz if it touches the positive you won t get any good connection. So from here. I m gonna stick it right through the loop hook.
It around and to make sure that it holds in place. I applied a little bit of solder. It was already a little bit at the end of the pen. So i just went ahead touched it up right at the end right here.
And that should be enough hold it in place so now what we re gonna do is we re going to add the negative wire and i m putting this in the other loop. Just gonna go as well a little bit to get a little bit of strength on there the wire was exposed while on that one so that won t slip it you to play to do there. I m gonna put a little bit of solder just to make sure that it actually holds for the entirety of this witch s life. That s moving as a switch for this led and from here we re going to connect the negative to the negative on the le and now we re going to test the leds.
So we re gonna put the battery in and we re gonna make sure everything works and if we wired everything right it should turn on and perfect. Now we have the on and off switch hooked up as well so we can turn it off and on whenever we want to use the leds. We re almost done guys so what we re gonna do now is we re gonna apply a little bit of hot glue on one side of the led strip that way we can secure it on to the visor make sure you do that to the other side as well and one for finish..
We can install it into our favorite helmet and we re done so as you can tell. It s not a very long or difficult process. It s something that you can do at home. And it doesn t take a lot of skill to do it as far as getting the materials.
The tcg s you can get online or at your local hardware store and ask for the stencil. You re gonna need a stencil cutter or someone you know that can cut you know hexagon patterns onto a vinyl. So yeah again thank you guys so much for watching this video. I hope you guys will give us a like on facebook and subscribe to our youtube channel lastly.
I d like to thank our two patients robert atactic for their continued support you guys are helping us reach our goals and we ve really appreciate that if this type of content is something that you guys really enjoy please consider being a patient on our food company. I ll leave a link in the description below again. Thank you guys so much for watching. And we ll see you ” .
Thank you for watching all the articles on the topic How to LED GLOW VISOR. All shares of bluevelvetrestaurant.com are very good. We hope you are satisfied with the article. For any questions, please leave a comment below. Hopefully you guys support our website even more.